Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateFast, Reliable Furnace Repair Across Kirby
Furnace repair in Kirby typically runs $150 – $700 depending on the part that failed, and most jobs are done in a single visit. Kirby’s 1950s – 1970s homes run original ductwork and often pair aging electric furnaces with newer condensers, so the fix isn’t always the obvious one. Our Furnace Repair team knows what to check first on these older Kirby systems, and we get to doors across Kirby fast. Call (903) 623-6784 and a real person answers, any hour.
Why Halden Heating and Air San Antonio Is Kirby’s Preferred Furnace Repair Company
Kirby homeowners call us because we show up when we say we will, with a live arrival time you can track on your phone, not a four-hour window. Every job gets a written price before we touch a tool, and every repair carries a written guarantee. Andre Fuller leads a team that has worked on hundreds of mid-century Kirby furnaces, and our techs know the streets here: Ackerman Road, Binz-Engleman, Wimbledon Drive, the neighborhoods around Kirby Middle School.
We’re part of the Relay Home Co. network, held to The Relay Visibility Guarantee on every job. That means before-and-after photos, a written report of what we found, and a 365-Day Done Right Promise. If a repair fails within the coverage window, we come back at no charge. No arguing. No fine print. That matters in Kirby, where a furnace that quits on a January night is a real problem in a slab-on-grade house with minimal insulation.
Styles & brands we work with
Furnace Tune Up in Kirby
A Furnace Tune Up in Kirby runs $80 – $200 and is the cheapest insurance you’ll buy for a heating system that sits idle nine months a year, then gets asked to work through a South Texas cold snap. Kirby’s long, dusty summers coat burners, blowers, and capacitors in fine grit, and the first cold front is when neglected parts fail. Our tune-up includes checking the heat exchanger for cracks, testing the ignitor and flame sensor, measuring blower motor amp draw, and verifying gas pressure if you have a gas furnace.
For most Kirby homes we recommend a tune-up every fall, before the first time you bump the thermostat past 68°F. If your furnace is from the 1970s or 1980s, or if it’s paired with a newer condenser, do it every year without exception.
Blower Motor Inspection
Older Kirby furnaces run belt-drive or early direct-drive blower motors that draw more amps as bearings wear. We measure actual amp draw against the motor’s rating plate. A motor pulling 2 amps over rating isn’t far from failure, and it’s also overheating your heat exchanger every cycle.
Heat Exchanger Safety Check
A cracked heat exchanger can leak carbon monoxide into a small Kirby house, and older furnaces don’t have the safety interlocks newer units do. We scope the exchanger on every tune-up, not just when a carbon monoxide detector trips. If we find a crack, we’ll show you photos before recommending repair or replacement.
Emergency Furnace Repair in Kirby
Emergency Furnace Repair in Kirby runs $150 – $700 and we answer calls 24/7 with a live person, because a furnace that dies at 2 a.m. in a 1960s Kirby ranch with single-pane windows is not something you wait until morning to fix. When the temperature drops into the 30s, those older slab homes lose heat fast, and a dark living room with a cold floor is a miserable place to wait for a callback that never comes.
Call (903) 623-6784 any hour. You’ll get a human, not a voicemail tree. We’ll give you a live arrival time and a written price before work begins. If the repair fails, the guarantee covers a free second visit, automatically.
Capacitor and Ignitor Failures
These are the most common emergency calls we see in Kirby. A capacitor is a small cylinder that gives the blower motor its starting jolt; when it fails, the furnace hums but won’t push air. An ignitor is the glowing element that lights the gas; when it cracks, you get no heat at all. Both are quick fixes we usually carry on the truck.
Blown Fuses and Tripped Breakers
Many 1950s and 1960s Kirby homes still run the original fuse panels, often without a dedicated breaker sized for a modern blower. A furnace that trips a breaker repeatedly is usually an electrical problem, not a furnace problem, and our techs check the load before replacing parts that don’t need replacing.
Trusted Brands We Service in Kirby
We service furnaces from Goodman, Rheem, York, Daikin, and most other major brands. Kirby’s housing stock means we see a lot of original General Electric and Westinghouse electric furnaces from the 1960s and 1970s, often paired with newer Goodman or Rheem condensers outside. Our trucks carry common ignitors, capacitors, flame sensors, and pressure switches for these setups, so we can finish most Kirby furnace repairs in one visit. When a part isn’t on the truck, our San Antonio parts network gets it to Kirby fast, usually same day.
Common Furnace Repair Problems We See in Kirby Homes
- Duct leaks and high static pressure. Original 1950s – 1970s ductwork in Kirby often leaks 20 – 30% of conditioned air into the attic or under the slab. A furnace that short-cycles or overheats is frequently fighting ducts that never got sealed, not a bad heat exchanger.
- Mismatched coils and condensers. A 1970s furnace paired with a newer outdoor condenser often has a mismatched evaporator coil. The refrigerant charge reads normal one day and wrong the next, and the system strains on triple-digit afternoons.
- Electrical panel limitations. Older Kirby fuse panels lack the dedicated circuit a modern variable-speed blower needs. Techs who skip the panel check install a furnace that trips breakers or fails inspection.
- Capacitor failures from attic heat. Kirby attics hit 130°F and higher for months. Capacitors and control boards mounted in or above the furnace degrade faster here than in cooler climates, which is why fall tune-ups matter.
See the difference
Before
After
Before
After
Before
AfterPricing for Furnace Repair in Kirby, TX
Furnace repair in Kirby runs $150 – $700 for most jobs. The range is driven by the part: a capacitor replacement lands near the low end around $150 – $250, an ignitor or flame sensor runs $180 – $350, and a blower motor or gas valve can push toward $500 – $700. Emergency calls cost the same as scheduled visits, because we don’t charge overtime for after-hours furnace repair in Kirby.
| Service | Typical Price in Kirby |
|---|---|
| Furnace Tune Up | $80 – $200 |
| Emergency Furnace Repair | $150 – $700 |
Every job gets a written price before we start. Call (903) 623-6784 for a free estimate and we’ll tell you what the repair will cost, in writing, before anything is done.
We Also Serve Cities Near Kirby
Halden Heating and Air San Antonio serves Furnace Repair in Kirby and the surrounding area, including San Antonio, Universal City, Timberwood Park, and Leon Valley. If you’re just outside Kirby, call (903) 623-6784 and we’ll route a tech your way with the same live arrival tracking and written pricing.
Serving Kirby, TX - Our Local Coverage Area
We’re based in the Kirby area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Kirby
The most common cause in Kirby’s 1950s – 1970s homes is leaking original ductwork, not the furnace itself. When branch ducts lose air into the attic or under the slab, the furnace has to run longer to hit the thermostat setting, and the farthest rooms never get enough airflow. A static pressure check will confirm it in under 30 minutes. Fixing the ducts usually costs less than replacing the furnace, often well under $700. Call (903) 623-6784 and we’ll test your system before recommending anything.
You can, but a like-for-like swap often disappoints in a Kirby home. The older furnace was sized for a different duct system, and a newer condenser may have a mismatched evaporator coil. If a tech drops in a new furnace without checking static pressure and coil match, the new unit can short-cycle just like the old one. We always test the ducts and coil before quoting a replacement, because that’s the only way to know what the new furnace actually has to handle.
Every fall, as part of an $80 – $200 tune-up. Kirby attics hold 130°F+ heat for months, and capacitors degrade faster in that environment than in cooler climates. A weakened capacitor still starts the blower, but it draws higher amps and will fail on the coldest night if you don’t catch it. We test every capacitor’s microfarad rating against the label, not just whether it starts the motor.
That’s dust burning off the heat exchanger and burners after sitting unused through a long Kirby summer. It usually clears in 20 – 30 minutes. If it smells sharp or electrical instead of dusty, or if the smell persists beyond the first cycle, shut the furnace off and call us. A persistent burning smell can mean a failing blower motor or overheated wiring, and that’s not something to wait out. Call (903) 623-6784 and we’ll check it.
Yes, and for many Kirby homes it’s the smartest fix. If only one or two rooms stay cold in winter, a ductless mini split solves that problem without touching the original ducts or the old furnace. It also gives you independent cooling in summer, which helps when the aging central system can’t keep up. We’ll give you a written price for either route before you commit, and there’s no pressure to replace the old furnace unless it’s actually unsafe or failing.
Call Halden Heating and Air San Antonio for Furnace Repair in Kirby
If your furnace is running but not heating, tripping breakers, or making sounds it shouldn’t, call (903) 623-6784. You’ll talk to a person, get a live arrival time, and see a written price before any work begins. Andre Fuller and our team serve Kirby every day, and every repair carries a written guarantee under the 365-Day Done Right Promise. Free estimates, no overtime charges for after-hours calls, and a free second visit if the repair fails. That’s how we do furnace repair in Kirby.
Written by Andre Fuller, Owner at Halden Heating and Air San Antonio, serving Kirby since 2004.